![[グリップのアップグレード] HOTLINEGAMES 2.0 Plus 滑り止めマウスグリップテープ Razer Viper V2 Pro Hyperspeedゲーミングマウススキンと互換性があり](/_next/image?url=https%3A%2F%2Fm.media-amazon.com%2Fimages%2FI%2F714vOcljzSL._AC_SL1500_.jpg&w=1920&q=75)
This article covers [グリップのアップグレード] HOTLINEGAMES 2.0 Plus 滑り止めマウスグリップテープ Razer Viper V2 Pro Hyperspeedゲーミングマウススキンと互換性があり, including what it fits, which grip styles benefit, how to apply it, and who should skip it.
Overview
The short version: this is a narrowly targeted accessory that pays off only if you already own a Razer Viper V2 Pro and can feel your fingers sliding on it. Its appeal is that it improves hold stability without replacing the mouse, and the listing carries 291 reviews with a 92% positive score (4.6 out of 5 stars) — a strong rating for an accessory in this class.
The 2.0 Plus revises the surface material of the earlier 2.0 line.
It uses a polymer with a US-made 3M adhesive layer and a diamond-pattern texture on top. Dry fingers catch on it, and when your hands sweat, the raised pattern gives moisture somewhere to go, so friction does not collapse all at once.
The box contains one full tape set (left/right buttons, side panels, rear), tweezers for placement, and a cleaning cloth.
Set expectations correctly before you buy. This tape changes nothing about sensor performance, polling rate, or weight balance.
The only thing it changes is friction where your fingers touch the shell. If your aim improves, that is a side effect of holding the mouse without gripping hard, not the tape correcting anything for you.
Who Benefits by Grip Style
The same tape feels very different depending on how you hold the mouse. Check which row describes you before ordering.
| Grip | How noticeable | Why |
|---|---|---|
| Fingertip | High | Contact is limited to a few points, so weak friction turns straight into wobble |
| Claw | High | The palm is lifted and the mouse is pinched by thumb and ring/little finger |
| Palm | Lower | The whole palm already supplies contact pressure, so slipping is rare |
In practice, a palm gripper who is not currently struggling with slip will not feel much for the money. Fingertip and claw users who catch themselves re-seating the mouse after a flick will notice it immediately.
Hand condition matters too: both sweaty hands and very dry hands improve over the bare shell. People in the middle see the smallest change.
Compatibility Guide
The set is pre-cut for the shell of the Razer Viper V2 Pro and Viper V2 Pro Hyperspeed, with separate pieces already shaped for the main buttons, both side panels, and the rear. No trimming is needed and the only tool required is the included tweezers.
No drivers or software are involved, so nothing about your mouse configuration or firmware is affected.
The important limit is that it does not transfer to other Razer mice. The Viper Mini, Viper 8K Hz, and DeathAdder V2 differ in length, waist position, and side wall angle; forcing the pieces on leaves lifted edges that become peel points.
The similarly named Viper V3 family is a different shape and a different product. Check the model marking on the underside of your mouse before ordering.
If you want tape for another mouse, Hotline Games also offers DIY sheets you cut yourself. The finish is less precise than a pre-cut set, but there is no model restriction.
Note also that this product is top and side grip only — it is not a set of mouse feet. Change the skates if you want different glide; use grip tape if you want a different hold.
Surface prep is part of compatibility. Oil left on the shell weakens initial adhesion, so wipe it down with the included cloth and work on a dry surface.
The added thickness makes the mouse very slightly bulkier, which is worth knowing if you carry it in a tight case or if your side-button reach is already marginal.
Product Info
| Item | Detail |
|---|---|
| Compatible mouse | Razer Viper V2 Pro / Viper V2 Pro Hyperspeed |
| Material | Polymer (US-made 3M) |
| Cut type | Pre-cut, model specific |
| Surface texture | Diamond pattern |
| Package includes | One grip tape set + tweezers + cleaning cloth |
The Amazon.co.jp price was ￥3,631 as captured on 2026-09-20.
That sits mid-pack for grip tape, and it is reasonable once you account for the model-specific cutting and the included tweezers. Small accessories like this move around a lot with sales, stock, and seller changes, so the figure here is a snapshot rather than today's price — always confirm the current price on the product page.
Marketplace listings such as eBay vary per seller, so compare shipping origin and delivery time as well as the headline number.
On reception, the listing shows 291 reviews at 92% positive (4.6 of 5 stars).
With a three-digit review count, that score is not the product of a handful of outliers. The usual source of low ratings in this price class is a botched first application or surprise at how strong or weak the adhesive feels, so reading the next section before you start is the cheapest insurance available.
Installation and Tips
Budget about fifteen minutes for your first attempt. Wipe the shell with the supplied cloth, dry-fit each piece for position and orientation before peeling the backing, then lay it down from one edge and push the air out as you go.
The tweezers exist so you never touch the adhesive face with your fingers, which matters most on the small pieces.
Three tips. First, do not start with the main buttons — they are the largest and most visible pieces, so a misalignment there stings the most.
Second, you have a few seconds to nudge a piece after placing it, but re-peeling after full pressure will cost you adhesion, so stop and reassess rather than pulling. Third, adhesives generally settle and strengthen over time after pressure is applied, so avoid heavy rubbing on the day you install.
Alternatives Compared
| Option | Rough cost | Effort | Result |
|---|---|---|---|
| Pre-cut set (this product) | ￥3,631 as captured 2026-09-20 | ~15 minutes | Edges follow the shell |
| Universal DIY sheet | Varies by product | Extra cutting work | Flexible but rougher edges |
| Nothing at all | Free | None | Hold degrades with sweat or dry skin |
| Buying a new mouse | An order of magnitude more | Re-tuning and re-learning | The shape itself changes |
The column to read is not cost but scope of change. Tape only alters the surface your fingers touch; it does not change shape or weight distribution.
If the shell itself does not suit your hand, tape will not fix that, and a different mouse is the honest answer. Tape treats the narrower complaint: the shape is right, but it slips.
Best Use Cases
- Competitive FPS and battle royale players: when a hold loosens for a fraction of a second mid-flick, the shot goes wide. More friction means less squeezing, which also reduces forearm fatigue over long sessions.
- Sweaty or seasonally dry hands: the diamond texture gives moisture an escape path, so grip does not drop off sharply when your hands get damp. In dry winter air, it also beats the bare shell.
- Anyone protecting the shell: the tape acts as a sacrificial layer against oil and abrasion, which helps if you plan to keep the mouse a long time or resell it later.
- Fingertip and claw grippers: the smaller the contact patch, the more directly extra friction translates into stability.
Skip it if you palm-grip and are not slipping, if you dislike a textured feel under your fingers, or if periodically re-applying a consumable sounds like a chore.
Before You Buy
First, this is not a mouse. Because the title contains the model name Razer Viper V2 Pro, and the listing is sometimes filed under gaming mice, buyers occasionally order it expecting hardware.
What arrives is tape, tweezers, and a cloth.
Second, it is a consumable. Depending on hours played and how much you sweat, the texture flattens and the edges start lifting as oil and dust work underneath.
Plan on re-applying every few months and budget accordingly; this is not a one-time fix.
Third, know how removal behaves. 3M-type adhesive is described as low-residue, but leaving a set on for a long time can leave grime along the edges.
Harsh solvents risk damaging the shell finish, so try a dry wipe first, then a well-wrung damp cloth.
Fourth, watch the side-button edges. If a piece overlaps the moving part even slightly, the click feel changes or the button catches.
After installing, press every button once and confirm nothing feels different.
Finally, a note on listing metadata. In the data behind this article, the price was captured from Amazon.co.jp at ￥3,631 (2026-09-20) while the seller and fulfilment fields read Amazon US.
Those fields can diverge from what the page actually shows and can change your shipping origin and delivery estimate. Confirm seller, dispatch origin, and delivery date on the page before ordering, and identify the product from the images and title rather than trusting the registered details alone — universal DIY versions and sets for other models often appear alongside it.
FAQ
Q. Does a mouse come with it?
A. No. You receive one grip tape set, tweezers, and a cleaning cloth.
Q. Will it fit a Razer Viper V3 or Viper Mini? A.
No. It fits only the Razer Viper V2 Pro and Viper V2 Pro Hyperspeed.
For other models, look for a DIY sheet you cut yourself.
Q. Can I reposition a piece? A.
Within the first few seconds, yes. Once fully pressed down, peeling it back reduces adhesion, so dry-fit with the tweezers before committing.
Q. How long does a set last? A.
It depends on hours of use and perspiration, but treat it as a consumable replaced every few months. Lifting edges are the signal.
Q. Does it add noticeable weight? A.
The added thickness and weight are minimal and do not undo the benefit of a lightweight mouse. The grip does get slightly thicker, which small hands may notice.
Q. Will it improve my aim? A.
Not directly. It removes slip-related re-seating, which can make aim more consistent, but if you were not slipping to begin with, expect little change.
Product Disclosure (Amazon)
- Manufacturer: Hotline Games
- Seller: Amazon US
- Fulfilled by: Amazon US
- ASIN: B0B2WMDK2H
- Note: This article covers a manufacturer-made product based on Amazon listing details.
