Epindon Thrustmaster eSwap X Pro Right Stick Tension Module

The Epindon module is a right-stick tension base module for the Thrustmaster eSwap X Pro controller. Swapping it in raises the stick's return force to 170g, which steadies micro-aim in FPS and TPS titles.

It is a light tuning part: you change the feel of the pad without replacing the pad.

Overview

The short version: this part exists for players who feel the stock right stick is too light, so their thumb slightly overshoots while tracking. If you don't have that specific complaint, there is little here for you.

The problem it solves is narrow, and whether it fits your complaint is the whole decision.

What gets replaced is the base module under the stick, not the thumbstick cap or lever — those are reused from the stock part. Nothing changes visually; what changes is how heavy the stick feels when pushed and how firmly it snaps back.

The body uses a metal structure, aimed at resisting the wobble that plastic bases can develop over time. In the box: one module and one screwdriver, so no extra tools are needed.

The platform row describes what the host controller supports, not something this module adds. Which systems you can actually play on follows your controller's own specification.

What 170g Actually Changes

170g is clearly on the heavy side for a gamepad stick. What matters is not the number but what it does in play.

The upside is resolution on small inputs. When you want to hold the stick at 10% deflection, a light stick turns thumb tremor into 15% or 5%; higher load shrinks that same tremor into a smaller angular error.

You notice it on long-range tracking and on recoil control, where the job is to hold a small, steady input. The stronger centering also returns the stick to neutral faster and cuts unintended residual drift.

The downside is the mirror image. Fast, wide flicks get heavier. Turning 180 degrees to answer a flank, or chasing someone strafing past you at close range, can feel slower than stock.

Long sessions also fatigue the base of the thumb more. If you play two or three hours at a stretch, take deliberate breaks for the first few days.

One practical warning: your aim will get worse before it gets better. You are rebuilding a force pattern.

Spend time in a firing range or against bots before taking the new feel into ranked play.

Compatibility Guide

The fit is narrow. Check three things before buying.

• Thrustmaster eSwap X Pro controller only. It won't transfer to other brands, and not to other Thrustmaster lines either. The eSwap family splits across generations and model numbers, so confirm the marking on your own unit.
• Right stick only. It does not mount on the left side. A separate model is required for the left stick; buying two of these will not cover both.
• Controller not included. This is a replacement part on its own.

Two installation details matter. First, contact alignment: the base module mates with the controller's connector through metal contacts, and forcing it in at an angle can damage them, leading to a stick that isn't detected or that drops inputs.

Remove the stock module with the included screwdriver, seat the new one flat, and press it straight down until fully home.

Second, the 0.8mm height difference.

The lever base sits about 0.8mm higher than stock, so the thumbstick cap can look seated when it is only partly on.

Press the cap fully down rather than resting it in place. A shallow fit means the cap can come off mid-match, or leave play between cap and base that undoes the very firmness you paid for.

After fitting, push the stick through all eight directions and tug gently to confirm it holds.

If the stick doesn't respond after the swap, insufficient seating is the usual cause. Remove it, inspect the contacts for dirt or deformation, and reseat.

If that fails, refit the stock module — that cleanly separates a controller-side fault from a module-side one.

Product Info

As captured on 27 August 2026, Amazon.co.jp listed this at ￥3,580; the same ASIN also showed ￥3,580 when captured on 2 June 2026.

Against replacing the controller itself, that is a cheap way to change how the pad feels. An eBay listing showed $45.00 as captured on 15 July 2026, which is higher than the domestic price once shipping, duties, and exchange rates are added — there is little reason to prefer it while local stock exists.

All of these are captured-at-the-time figures and move with sales and stock. Check the product page for the current price before buying.

The rating is 4.1 out of 5 stars (equivalent to 82% positive), but it rests on only 5 reviews.

At that sample size, treating a high score as evidence of quality is risky: one bad review swings the average sharply, and nothing statistical about defect rates can be read from it. This is normal for niche third-party accessories, so check the return terms and warranty before you weigh the star rating.

Warranty runs one month from purchase. Since there is no long coverage, open the package immediately, install it, and verify operation on the spot.

Sitting on it for two months means even a genuine defect falls outside the window.

Product Disclosure (Amazon)

• Manufacturer: Epindon
• Seller: Epindon JP
• Fulfilled by: Amazon
• ASIN: B0BX3SRPDN
• Note: This article covers a manufacturer-made product based on Amazon listing details.

Best Use Cases

The purchase likely pays off if any of these describe you.

• You already own an eSwap X Pro and find the right stick too light. Nearly all of the value sits on this single point.
• You play competitive FPS/TPS and struggle with long-range fine adjustment. The more your style depends on holding small, sustained inputs — recoil control, pre-aim — the more you will feel it.
• You like tuning pad feel yourself. The eSwap X Pro is built around swappable modules, so you can deliberately run different weights left and right. No soldering, no teardown, just the bundled screwdriver.
• You want a different feel without buying a new controller. It is reversible: keep the stock module and you can go back.

Conversely, if you don't own the controller, want the left stick heavier, or mostly play racing and action-adventure titles with lots of wide camera sweeps, this is a low-priority purchase.

Pre-Purchase Notes

The biggest trap is that it presumes you own the controller. Because the listing name contains "Thrustmaster eSwap X," it reads like the controller itself in search results.

What arrives is one palm-sized base module and one screwdriver.

Right stick only, again. Two of these will not give you a heavy left stick; that needs a different model.

Heavier is not automatically better. The right tension depends on your style, hand size, and grip strength, and 170g is not universally optimal.

If you already run low stick sensitivity, adding weight tends to push you further toward "my turn didn't finish in time." Tune sensitivity first; consider this only if fine adjustment still feels unstable afterwards.

Damage during installation may not be covered. Forcing a misaligned module home, or prying the cap off with a tool, causes physical damage — and the warranty is only one month.

Work in good light and without force.

Also, listing metadata sometimes disagrees with the physical product. In this accessory category it is not unusual to see muddled compatibility text or price entries whose store label doesn't match the site actually selling it — this listing shows exactly that kind of mismatch in part of its price information.

Don't trust the listing text alone: confirm from the product images and title that you are buying a standalone right-stick base module. If anything is unclear, ask the seller which controller it fits; that is cheaper than a return.

Finally, with only 5 reviews, nothing can be concluded about unit variance or defect rates. Buy on the assumption that you will verify operation the day it arrives and act within the warranty window if something is wrong.

FAQ

Q. Will it fit controllers other than the eSwap X Pro? A.

No. It is exclusive to the Thrustmaster eSwap X Pro controller and does not transfer to other brands or lines.

Q. Can I use it on the left stick?
A. No. It is right-stick only; a separate model is required for the left side.

Q. Is a thumbstick cap included?
A. No. The box contains one base module and one screwdriver; you reuse the stock cap and lever.

Q. Does installation need soldering or disassembly? A.

No. Remove the stock module with the included screwdriver and seat the new one.

Just press the metal contacts in straight, and fully seat the cap — the lever base sits about 0.8mm higher than stock.

Q. Can I revert if I don't like it?
A. Yes, provided you keep the stock module you removed. Strongly recommended.

Q. What does it cost? A.

Amazon.co.jp showed ￥3,580 as captured on 27 August 2026.

Prices change, so check the product page at purchase time.