# Lian Li UNI FAN SL INFINITY 120 White 3-Pack: Wiring and Who Should Skip It

> Daisy-chain wiring, controller needs, and who should skip the Lian Li UNI FAN SL INFINITY 120 3-pack.

Tags: case-fan, lian-li, argb, 120mm, white-build, daisy-chain, infinity-mirror
Source: https://www.amazon.co.jp/dp/B0B4SKMYJT
Article page: https://web-autoai.com/articles/lian-li-uni-fan-sl-infinity-120-3pack?lang=en

Prices and ratings change over time — check the article page for the current values.

---

## Overview

The Lian Li UNI FAN SL INFINITY 120 is sold here as a three-pack of white PWM PC cooling fans, bundled with a controller hub and cables. The short verdict: it is a strong pick if you want to show off your fans through a glass panel and cut down fan cabling. It is a poor fit if you simply want cheap airflow or expect it to behave like ordinary 4-pin fans. Rated specs are 2100 RPM maximum speed, 29 dBA noise, and 3.5 W power draw per fan.

The headline feature is the modular linking system: adjacent fans slide together, and power and signal pass through the joints. That means you no longer route a separate cable for every fan, which greatly reduces clutter behind the motherboard tray. One linked group holds up to four fans. Note that only the fan-to-fan link is toolless; the fans are still screwed to the case as usual.

The second feature is the infinity mirror on the center hub and the inner edge of the frame. LED light reflects between mirrored surfaces so it appears to recede in layers. Combined with the white housing, it suits an all-white build. On Amazon. co.

## Compatibility Guide

The fans measure a standard 120mm x 120mm x 25mm, so they physically fit any case or radiator with 120mm mounts. In practice, the common failure points are not the screw holes but the width of a linked chain and the cable routing. Linked fans behave like a single rigid strip, so cases with non-standard spacing between 120mm mounts may not accept them while linked.

Power and signal run over a proprietary 7-pin cable to the included controller hub. On the motherboard you need one free PWM header for speed control and one 5V 3-pin ARGB header for lighting sync. A 5V ARGB header is not the same as a 12V 4-pin RGB header, and plugging into the wrong one can damage the LEDs. Check your motherboard manual for the 5V 3-pin label before connecting.

Lian Li's L-CONNECT 3 software gives fine control over fan speed and lighting, and the fans can also sync with ASUS Aura Sync, MSI Mystic Light, and Gigabyte RGB Fusion. Software control typically means connecting the controller to an internal USB header, so confirm you have a spare one and check how the controller is powered in the included manual.

| Check | What you need | Common mistake |
|---|---|---|
| Mounting | 120mm fan mounts | Linked spacing does not match the case |
| Speed control | 1 free PWM header | Headers already used by other devices |
| Lighting sync | 1 ARGB header (5V 3-pin) | Confusing it with a 12V RGB header |
| Software control | L-CONNECT 3 | No spare internal USB header |
| Power | About 10.5 W for three fans | Almost never a PSU concern |

As the table suggests, this kit is more likely to be blocked by a shortage of motherboard headers than by physical size. Mini-ITX boards in particular have few fan and USB headers, so count them against your AIO pump and front-panel USB before buying. At roughly 10.5 W for all three fans, power supply sizing is effectively unaffected.

## Product Info

The box contains three fans, a controller hub, and cables. The listed materials are an aluminum frame with plastic blades, and the rated voltage is 12V. Released in 2022, this model combines the UNI FAN linking system with infinity mirror lighting.

| Item | Spec |
|---|---|
| Fan size | 120mm x 120mm x 25mm |
| Max speed | 2100 RPM |
| Noise level | 29 dBA |
| Power draw | 3.5 W per fan |
| Voltage | 12V |
| Material | Aluminum frame, plastic blades |
| Contents | 3 fans, controller hub, cables |

Amazon. co. Check the retailer's page for the latest price. That is clearly more than a generic 120mm fan, but with the controller hub included it is not far from other ARGB fans in the same class. Prices move often with sales and stock, so check the product page for the current price before buying.

## Comparison With Competitors

Showcase fans differ mainly in how they reduce cabling and which control ecosystem they lock you into. Deciding on the hub and software ecosystem first, before comparing lighting styles, avoids most regrets.

| Product | Cabling approach | Best for |
|---|---|---|
| Lian Li UNI FAN SL INFINITY 120 | Slide-together links into a dedicated hub | Builders who want both looks and tidy cables |
| Corsair LL120 RGB | One cable per fan, gathered by Corsair controllers | Users standardizing on iCUE |
| Thermaltake SWAFAN EX12 ARGB | Magnetic linking | Users in the Thermaltake ecosystem |
| Corsair iCUE LINK RX120 RGB | Single-cable chain into a system hub | Builders adopting Corsair's newer system |
| NZXT F120P v2 | Conventional non-RGB PWM fan | Users prioritizing pressure and quiet over looks |

Against the Corsair LL120 mentioned in the original article, this kit's advantage is fewer cables. If you want everything unified under iCUE with other Corsair gear, though, the LL120 or iCUE LINK keeps management simpler. If you do not need lighting at all, a non-RGB fan such as the NZXT F120P costs far less per fan.

## Planning the Wiring

To avoid rework, plan these points before installing.

1. **Decide intake and exhaust.** For example, front intake and top or rear exhaust.
2. **Split the linked groups.** Each group holds up to four fans. Fans in one group are meant to be controlled together, so separate intake and exhaust into different groups if you want different speeds.
3. **Count your headers.** PWM, 5V 3-pin ARGB, and a spare internal USB header if you plan to use L-CONNECT 3.
4. **Check orientation and looks.** Flipping a fan also changes which way the mirror face and link connectors point. If you want intake and exhaust fans to look the same, compare how each orientation looks in the product images first.

Steps 2 and 3 are the ones that force you to pull fans back out if missed. Also make sure there is room behind the motherboard tray to mount the controller hub.

## Best Use Cases

- **Gamers showing ARGB through a glass panel:** The layered infinity mirror effect looks best in cases with a transparent side panel, and L-CONNECT 3 lets you fine-tune patterns to match the rest of your setup.
- **Builders who want fewer fan cables:** Linking turns several fan cables into one run, making cable management and later cleaning or swaps easier.
- **All-white builds:** The white housing blends with white cases, motherboards, and graphics cards, and a three-pack keeps every fan visually consistent.
- **Users who tune fan curves for quiet:** The rated noise level is 29 dBA, and a conservative fan curve keeps the system unobtrusive during everyday work.

## Things to Consider

**Not a general-purpose fan. ** The kit relies on the included controller hub and does not work like a standard 4-pin fan plugged straight into the motherboard. Mixing it with other brands tends to split control between the motherboard, L-CONNECT 3, and another vendor's software.

**Four fans per linked group. ** Builds with a radiator plus several case fans need a plan for how groups map to controller ports. UNI FAN has several generations and variants, and different generations may use different connectors or controllers. When adding fans later, confirm by model number that they are SL INFINITY parts.

**Read the noise figure as a rated value. ** 29 dBA is the manufacturer's published spec, not a promise of how quiet the fans feel at a constant 2100 RPM. The original article claimed they stay quiet under heavy load, but real noise depends on the case and the speed you set. If silence matters, plan on running a gentle fan curve.

**The case decides the value. For hidden fans, a non-RGB model is better value.

**Software dependence. ** Detailed setup is done in L-CONNECT 3. If you avoid background utilities or want motherboard-only RGB control, consider whether ARGB sync alone will satisfy you.

## FAQ

**Q. Can I plug the fans directly into a motherboard fan header? **
A. Normally they connect through the included controller hub, which then connects to one PWM header and one 5V 3-pin ARGB header.

**Q. Can I add a fourth fan later? **
A. Yes. A linked group supports up to four fans, as long as the added fan is an SL INFINITY part. Other UNI FAN generations may not be compatible, so check the model number.

**Q. Do the lights work without the software? **
A. Connected to an ARGB header, they sync with motherboard tools such as ASUS Aura Sync, MSI Mystic Light, and Gigabyte RGB Fusion. L-CONNECT 3 offers more detailed pattern control.

**Q. Can I mount them on a radiator? **
A. Physically yes, since they are standard 120mm x 25mm fans. The provided specs do not list static pressure, so check the manufacturer's page if radiator performance matters.

**Q. Do I need a bigger power supply? **
A. No. At 3.5 W per fan, the three fans draw about 10.5 W in total.

### Product Disclosure (Amazon)
- Manufacturer: LIANLI
- Seller: Amazon.co.jp
- Fulfilled by: Amazon.co.jp
- ASIN: B0B4SKMYJT
- Note: This article covers a manufacturer-made product based on Amazon listing details.
